Installation and adjustment of double roller extrusion granulation machine
The roller extrusion granulator is a granulation machine. It can make pellets without drying process at room temperature. The equipment has low investment, quick effect and good economic benefits.
The complete set of equipment is compact, scientific and reasonable, and advanced in technology. Meanwhile, it is energy saving and the operation is easy and reliable. What's more, you can maintain it conveniently. The raw material has wide adaptability and this machine is suitable for granulating various raw materials such as compound fertilizer, medicine, chemical industry and feed. And the product has high granulation rate.
This double roller extrusion pelletizer can produce various concentrations, multiple types (including organic fertilizer, inorganic fertilizer, biological fertilizer, magnetic fertilizer, etc.) compound fertilizer. In particular, the granulation of rare earth, potash and ammonium bicarbonate series compound fertilizers has filled the domestic gap.
2. Circumferential alignment: The steps of the circumferential alignment are as follows: Unload the 6 consecutive bolts of the driven gear and the adjusting sleeve, so that the adjustment and the passive gear are slightly disengaged. Since the design has already tested a ball and socket adjustment, It is equipped with two adjustment bolts, so the misalignment can be adjusted regardless of the misalignment.
3. Because the ball socket is too small, the carton board is placed between the two rollers during the adjustment. After rolling, each project must have a process. The organic fertilizer equipment is also completed by step by step installation, so it is inevitable. There will be some steps, which is a process that must be taken.
In production, sometimes it is necessary to increase the output or increase the bite angle. At this time, the distance between the two shafts can be increased, and the distance between the driving shaft roller and the driven shaft can be increased. The steps are as follows: stop, remove the passive shaft The two ends of the cover are pressed, and the inner two eccentric sleeves are rotated in the same direction. One position at a time, the rollers cannot collide with each other, and should be kept between 0.3-1 mm.
2. The adjustment of the ball socket
The ball socket is formed by the dimples of the main roll surface, so there is a problem of axial alignment and circumferential alignment.
The complete set of equipment is compact, scientific and reasonable, and advanced in technology. Meanwhile, it is energy saving and the operation is easy and reliable. What's more, you can maintain it conveniently. The raw material has wide adaptability and this machine is suitable for granulating various raw materials such as compound fertilizer, medicine, chemical industry and feed. And the product has high granulation rate.
This double roller extrusion pelletizer can produce various concentrations, multiple types (including organic fertilizer, inorganic fertilizer, biological fertilizer, magnetic fertilizer, etc.) compound fertilizer. In particular, the granulation of rare earth, potash and ammonium bicarbonate series compound fertilizers has filled the domestic gap.
 |
| Tongda roller extrusion granulator |
How to install a roller press granulation machine?
1. Axial alignment: It has been adjusted during installation. When you need to adjust it, tighten or loosen the gland on both sides of the passive bearing housing.2. Circumferential alignment: The steps of the circumferential alignment are as follows: Unload the 6 consecutive bolts of the driven gear and the adjusting sleeve, so that the adjustment and the passive gear are slightly disengaged. Since the design has already tested a ball and socket adjustment, It is equipped with two adjustment bolts, so the misalignment can be adjusted regardless of the misalignment.
3. Because the ball socket is too small, the carton board is placed between the two rollers during the adjustment. After rolling, each project must have a process. The organic fertilizer equipment is also completed by step by step installation, so it is inevitable. There will be some steps, which is a process that must be taken.
Tips for adjustment of double roller machine
1. Pressure roller gap adjustmentIn production, sometimes it is necessary to increase the output or increase the bite angle. At this time, the distance between the two shafts can be increased, and the distance between the driving shaft roller and the driven shaft can be increased. The steps are as follows: stop, remove the passive shaft The two ends of the cover are pressed, and the inner two eccentric sleeves are rotated in the same direction. One position at a time, the rollers cannot collide with each other, and should be kept between 0.3-1 mm.
2. The adjustment of the ball socket
The ball socket is formed by the dimples of the main roll surface, so there is a problem of axial alignment and circumferential alignment.
During the installationm, adjustment and the operation, there may be many problems. Tongda granulation machine manufacturer can provide you professional after-sale service for helping you.
Comments
Post a Comment